Shop FEYNLAB Ceramic Wheel & Caliper

FEYNLAB · Protection

Ceramic Wheel & Caliper

$79.95incl. GST

Size
  • Free click & collect from Nunawading
  • Shipped Australia-wide
  • Questions? Call 0475 000 066 or email info@shoyi.com.au

Ceramic Wheel & Caliper is a thick, high-solids nano ceramic coating made for wheels and brake calipers, where heat, brake dust and road contamination are constant. At 70% solids it builds a tough layer that stands up to daily abuse and makes wheel cleaning far easier. Designed for clear-coated painted wheels, calipers and chrome.

Key features

  • 70% solids content builds a thick, durable layer of protection.
  • Formulated for high temperatures and constant contamination from brake dust and road grime.
  • Makes wheels and calipers much easier to clean.
  • One layer delivers 1 year of durability on clear-coated painted surfaces.
  • Pairs with Overcoat for added hydrophobic and self-cleaning performance and easier maintenance.

Specifications

Application temperature 10°C to 30°C
Compatible with Overcoat
Cure Infrared curing required: 60°C surface temperature for 15 minutes per panel
Durability 1 year
Dwell time 25 to 30 minutes
Film build 1 to 2 microns (1 component layer)
Shelf life Unopened: 1 year. Opened: use within 30 days
Solids content 70%
Time between layers At least 1 hour, no more than 3 hours

Approved surfaces

  • Clear-coated painted wheel rims and calipers
  • Chrome surfaces

In the box

  • 30ml Ceramic Wheel & Caliper

Preparation

  1. Thoroughly clean wheels and calipers with Feynlab Pure Wash to remove all topical contamination.
  2. Follow with a topical decontamination clay treatment using Feynlab Prime.
  3. If necessary, use a ferrous iron removal product to remove all embedded iron deposits.
  4. Clean and polish to the desired level.
  5. Remove all polish oils with Feynlab Panel Prep to ensure optimal bonding and durability.

Directions

  1. Place the vehicle in a well-lit, temperature-controlled (10°C to 30°C), contamination-free environment.
  2. Have 6 or more new microfibre towels, 2 or 3 microfibre sponge applicators and 1 foam applicator on hand before starting.
  3. Shake vigorously for 2 minutes. Open the bottle and allow the coating 1 minute of air exposure.
  4. Apply a small amount to a microfibre applicator and spread evenly over the wheels or calipers, using enough to coat evenly without over-saturating.
  5. Work a maximum area of 2 full wheels or 4 wheel faces before wiping off.
  6. Allow to dwell for 25 to 30 minutes. Dwell times over 40 minutes make removal much more difficult.
  7. Remove the coating with a microfibre towel, following the same pattern as application.
  8. During the final wipe, inspect for leftover residue (high spots), especially on edges, emblems and tight areas. High spots are much easier to remove within 20 to 40 minutes of the final wipe.
  9. For extra thickness, apply another layer at least 1 hour after the final wipe of the first. For best results layer within 1 to 3 hours; do not layer after 3 hours.
  10. Infrared curing is required: bake each panel with an IR lamp to a surface temperature of 60°C for 15 minutes, at a distance of approximately 76 to 91 cm.

Aftercare

  1. Avoid any incidental water exposure for 24 hours. If it occurs, gently wipe the water off.
  2. Avoid all chemicals, including car washes, for 7 days.
  3. If the vehicle must be released in wet conditions within 24 hours of the final coat, apply Feynlab Detailer after 2 to 4 hours of curing.
  4. Wash and maintain with Feynlab Pure Wash or Feynlab Pure Rinseless.

Cautions

  • Always wear a respirator and gloves during application.
  • Ensure the application area is free of loose contamination.
  • Apply only to approved surfaces. Do not apply to unapproved surfaces.
  • Do not let the coating dwell beyond 40 minutes, as removal becomes much more difficult.
  • Do not apply an additional layer more than 3 hours after the previous one.
  • Higher humidity speeds curing. At 75% humidity or higher, consider shortening the recommended dwell and wipe times.
  • Moving air shortens dwell times where it contacts the coating, so stop moving air as much as possible during application.
  • Coatings are best applied in a temperature-controlled environment of 10°C to 30°C, with humidity as low as possible.

From the studio

Shoyi is an authorised FEYNLAB trainer and installer and an official FEYNLAB distributor, so this is the range we use on customer cars in the Nunawading studio, not something we have only read about.

Not sure it suits your car? Call 0475 000 066 or email info@shoyi.com.au and we will point you the right way. Related reading: Is ceramic coating worth it?, Why Melbourne summer is hard on paint, How to wash a PPF-protected car.

Authorised & Certified Installer
SunTek authorised installerFEYNLAB certified installerAutoArmorModBox Works
Sister company ofAuto Marquee Group
Site created byModBox Works