Shop / FEYNLAB / Black Velvet Tire Sealant
FEYNLAB · Protection
Black Velvet Tire Sealant
- Free click & collect from Nunawading
- Shipped Australia-wide
- Questions? Call 0475 000 066 or email info@shoyi.com.au
Black Velvet Tire Sealant is a water-based tyre protectant that dries to a flexible latex film anchored into the pores of the sidewall. It shields rubber from UV, ozone and weather, leaves a deep black finish and stays put rather than slinging onto the paintwork. It is FEYNLAB's longest lasting tyre protectant for home users, and can be layered from a satin, like-new look to a high shine.
Key features
- Lasts up to 6 months with regular maintenance washes, longer than All Purpose Dressing
- Protects rubber from UV and ozone degradation, dry rot and cracking
- Sling-free film anchors into the tyre pores instead of sitting on the surface
- Resists build-up of brake dust, dirt and grime, and is easy to clean
- Layer it to choose a gloss level from satin like-new through to very shiny
- Solvent and silicone free, so it is body shop safe
Specifications
| Base |
Water-based, solvent and silicone free |
| Compatible with |
Can be used for maintenance over previously applied Tire Coating |
| Drying time |
At least 10 minutes before driving |
| Durability |
Up to 6 months (2 to 6 months depending on weather, driving and cleaning conditions) |
| Finish |
Satin to very shiny, adjustable by layering |
Approved surfaces
- Black rubber tyres only (will stain white lettering or decals)
- May be used for maintenance over previously applied Tire Coating
In the box
- 120 ml bottle of Black Velvet Tire Sealant
Preparation
- Clean the tyres thoroughly with Tire & Wheel Cleaner to remove any previously applied silicone products.
- Allow the tyres to dry completely before applying.
Directions
- For a first application, apply 2 coats, as the first coat is partly absorbed into the pores of the tyre (a desired effect).
- Apply a generous amount of sealant onto a microfibre or foam applicator.
- First coat: work the sealant into the pores of the rubber, moving evenly around the tyre without touching the wheel.
- If product gets on the wheel, remove it quickly with a microfibre towel and Panel Prep before it sets up.
- Second coat: wait a few minutes, then apply evenly in long lines covering about a quarter of the tyre at a time until the whole tyre is covered.
- Work around the vehicle to cover all 4 tyres, including the spare.
- Allow 10 minutes of drying time before driving.
Aftercare
- Allow at least 10 minutes to dry before driving to avoid sling and runs.
- Wash and maintain with Pure Wash or Pure Rinseless, using a soft-bristled brush or microfibre towel.
- Reapply a single layer when the gloss has faded, usually every few months depending on conditions.
- For a maintenance layer, wash the tyre with Pure Wash or Pure Rinseless and a soft-bristled brush, let it dry, then apply one coat evenly and allow 10 minutes before driving.
Cautions
- Always wear a respirator and gloves during application.
- Make sure the application area is free of loose contamination.
- Do not apply to unapproved surfaces. Use on black rubber tyres only, as it will stain white lettering and decals.
- May stain wheels: wipe off any accidental contact with other surfaces immediately.
- Will stain flooring: place a tarp or cardboard under the tyres to protect floors.
- Do not clean coated tyres with Tire & Wheel Cleaner, as its chemicals will prematurely degrade the sealant.
- Do not scrub aggressively with a hard-bristled brush or other abrasive tool, as this will prematurely degrade the sealant.